Compatible-systems MicroRouter 900i Manual do Utilizador Página 1

MicroRouter 900iInstallation GuideCompatible Systems Corporation4730 Walnut StreetSuite 102Boulder, Colorado 80301303-444-9532800-356-0283http://www.

Chapter 2 - Getting Started 5Chapter 2 - Getting StartedA Few NotesPlease Read The ManualsThe manuals included with your MicroRouter 900i contain so

6 Chapter 2 - Getting StartedWhat You Will Need To Get StartedBefore connecting the MicroRouter 900i, please check the list below to make sure that y

Chapter 2 - Getting Started 7Thick EthernetTo connect the router’s Ethernet port to a standard (thick) Ethernet cable you will need a transceiver ca

8 Chapter 2 - Getting StartedThe MicroRouter 900i includes one DIN-8 to DB-25 RS-232 sync/async data cable. This cable supports RS-232 asynchronous

Chapter 3 - Network Installation 9Chapter 3 - Network Installation900i MicroRouter Back PanelThis section of the manual describes how to connect the

10 Chapter 3 - Network InstallationFor wall mounting, follow the instructions included with the wall-mount bracket kit.Connecting the Router to the E

Chapter 3 - Network Installation 11router must first be configured for synchronous operation before connecting to the device. See Chapter 6 - Basic

Chapter 4 - CompatiView Software Installation 13Chapter 4 - CompatiView Software InstallationAll of the routers in Compatible Systems’ internetworki

MicroRouter 900i Installation Guide, Version 3.0Copyright© 1999, Compatible Systems CorporationAll rights reserved. RISC Router and CompatiView are t

14 Chapter 4 - CompatiView Software Installationwhich it should locate CompatiView and its associated files and data-base subdirectory.Once the insta

Chapter 5 - Setting Up Command Line Management 15Chapter 5 - Setting Up Command Line ManagementThe command line interface allows you to configure an

16 Chapter 5 - Setting Up Command Line Managementernet interface. You can then do the following:1. Set the host’s IP address to 198.41.12.2, with a C

Chapter 5 - Setting Up Command Line Management 17using the IP transport protocol), or anywhere on your network (if using the IPX transport protocol)

.

Chapter 6 - Basic Configuration Guide 19Chapter 6 - Basic Configuration GuideThis chapter briefly discusses the major parameters that must be set in

20 Chapter 6 - Basic Configuration GuideIP ProtocolRequired for IPThese parameters set the basic address characteristics of the interface. They prov

Chapter 6 - Basic Configuration Guide 21parameters will depend on the line communications device you are using.v Note: Frame Relay and SMDS are pre

22 Chapter 6 - Basic Configuration GuideSuggested for Dial-On-Demand OperationThis mode of operation is only supported on the WAN RS-232 inter-face.

Chapter 6 - Basic Configuration Guide 23operation when you are connecting to another Compatible Systems router at the other end of the link.Frame Re

iiiChapter 1 - Introduction 1ABOUT THE MICROROUTER 900I 1A NOTE ABOUT ON-DEMAND INTERNETWORKING 1MICROROUTER 900I INSTALLATION OVERVIEW 1Chapter 2 - G

24 Chapter 6 - Basic Configuration GuideTB: Use configure and set the DLCI keyword in the Frame Relay WAN 0 section.IP ProtocolRequired for IPThere

Chapter 6 - Basic Configuration Guide 25TB: Use configure and set either the RIPVersion keyword or the OSPFEnabled keyword in the IP WAN 0 section

Appendix A - Shipping Defaults 27Appendix A - Shipping DefaultsDefault Password• letmeinEthernet PortIP Defaults• On• Address: 198.41.12.1• Subnet M

Appendix B - Connector and Cable Pin Outs 29Appendix B - Connector and Cable Pin OutsPin Outs for DIN-8 to RS-232 Data Cable (DCE/Male)Notes:1. DCD

30 Appendix B - Connector and Cable Pin OutsNotes:1. This cable is a null-modem DTE-to-DTE cable.2. Because it is a null-modem cable, it can be conne

Appendix C - Light Patterns and Test Switch Settings 31Appendix C - Light Patterns and Test Switch SettingsMicroRouter 900i Light PatternsThe MicroR

32 Appendix C - Light Patterns and Test Switch SettingsMicroRouter 900i Switch SettingsM Caution: Settings marked with an asterisk may erase your Fl

Appendix D - Downloading Software From Compatible Systems 33Appendix D - Downloading Software From Compatible SystemsWe make the latest versions of

iv Connecting an Out-of-Band Management Console 11Powering Up the Router 11Chapter 4 - CompatiView Software Installation 13CompatiView for Windows 13S

.

Appendix E - Terms and Conditions 35Appendix E - Terms and ConditionsCompatible Systems Corporation (Compatible Systems) offers to sell only on the

36 Appendix E - Terms and ConditionsTo obtain service under this Warranty, the Customer (or subsequent pur-chaser, if applicable) must follow the pro

Appendix E - Terms and Conditions 37ber of each item being returned; (c) original Compatible Systems Sales Agreement number; and (d) any special ins

38 Appendix E - Terms and Conditions

vIP Protocol 24Required for IP 24Required for IP Numbered Interface 24Required for IP Unnumbered Interface 24Suggested for IP 24SAVING A CONFIGURATION

vi

Chapter 1 - Introduction 1Chapter 1 - IntroductionAbout the MicroRouter 900iCongratulations on your purchase of the MicroRouter 900i Ethernet to Int

2 Chapter 1 - IntroductionIn short, the installation steps are:1. Install the MicroRouter hardware and connect it to a line commu-nication device (in

Chapter 1 - Introduction 3AppendicesThis part of the manual includes additional information that might be of interest to you such as technical speci